Hobbyists and carpenters use table saws as a way to make accurate and completely level cuts on wood and other materials. While most of these tables come with some type of saw blade, you may need to replace that one because of the materials that you use or because of the thickness and sizes of those materials.
We think the Woodworker II from Forrest (Check Price on Amazon.com) is the top model that money can buy because it has a design that lets you cut down on wood waste. It also lets you easily feed and move wood across and has a design that brings it to a complete stop when the saw stops. Check out other products on our list to find those suitable for cutting wood and other materials.
Top 10 Table Saw Blades Comparison Chart 
The 10 Best Table Saw Blades - Reviews
1. Forrest Woodworker II
This product landed in our top spot because so many customers refer to it as the Cadillac of saw blades. It has a standard 10-inch size that works with most tables from different manufacturers and comes with 40 individual teeth around the sides. The 30-degree angle of those ATB teeth help it reach a full stop when you turn off the power.
Designed to reduce the splintering that can sometimes occur, the Woodworker II also reduces the jump that can occur when moving wood because you can more easily feed boards across it. It has a kerf design that helps prevent wood loss too.
ATB teeth placed at a 30-degree angle help it come to a complete stop faster
Measures 10-inches across with 40 individual teeth along the edges
Reduces the risk of wood splintering
Moves fast enough that it can burn some types of wood
Does not work well with a zero clearance setting
2. Forrest Woodworker II with 15-Degree ATB
Though similar to our number one choice, this Woodworker II has ATB teeth at a 15-degree angle rather than a 30-degree angle, which may be a little too short or low for your needs. It still helps reduce the amount of wood that you waste by up to 20% and comes with individual teeth that prevent splintering. Some found that it’s so thick that it may not work with their tables and that it makes their wood burn.
This one reduces splintering when making radial cuts and helps prevent top splintering when using plywood and thinner boards. It also gives you more control when pushing and pulling boards across the spinning blade.
Helps you save up to 20% on the loss of wood that you usually experience
Comes with 15-degree ATB teeth that stop wood from splintering on the top and bottom
Provides better control when pushing and pulling boards
ATB degree angle may be too short for your needs
Is thicker than others and may not fit your table
3. Freud 40-Tooth General Purpose
Whether cutting flooring for your home or wood for a project, this Freud option is a good choice because it is effective when used with different types of woods as well as laminates. It cuts through that wood smoothly and cleanly, but it can leave behind burn marks on certain types of wood. The 40 individual teeth around the edges provide smooth cuts without splintering the wood.
Freud used lasers to cut each of those teeth, which makes the sides smoother and keep the teeth from clinging to the wood. It also comes with a surface coating that keeps sawdust from building up on the surface and makes it resistant to rust.
Moves through most types of woods smoothly and cleanly
Surface coating protects against build up and rust
Designed for use with woods and laminates
May leave burn or scorch marks on certain types of wood
Teeth can wear down after multiple cuts
4. Freud 80-Tooth Ultimate
This model comes with the same coating as the last model, which makes it resistant to rust and keeps build up from impacting its strength and finish. It has twice as many teeth on it though, and those 80 teeth provide the smooth and clean cuts that you want without chipping or splintering. Those ATB teeth can break off or wear down when you use this one with harder materials.
Designed for cutting laminates and woods, this product works on marine-grade products and on veneers too. Made from a high-density carbide material, this model is stronger than others and will last longer.
Designed to work on laminates and woods with a veneer finish/coating
Made from a high-density carbide with ATB teeth
Perma-SHIELD coating prevents common damage to the teeth and surface
Can cheap some thinner and cheaper types of wood
Teeth can break off when used on harder materials
5. DEWALT Series 20 10-Inch
Finer and thinner than other similar products, this model from DEWALT comes in a standard 10-inch size and includes two models of the same size in each package. The manufacturer used computers to create the perfect balance to each one, which allows for the smooth cuts that you want. Each one features 60 individual teeth evenly spaced around the edges.
Those teeth have a unique wedge shoulder design that provides a small shoulder behind each teeth. This puts more power behind those teeth when cutting and creates finished cuts that are smoother with less splintering and chipping along the edges.
DEWALT uses computers to create the perfect balance
Wedge shoulder design of the tips adds more strength to those tips
Comes with two products of the same dimensions
Teeth will only last through a few sharpening stages
Has a thinner thickness than others do
6. Overpeak 80-Tooth ATB
The bright blue finish of this Overpeak model reduces the risk of accidents because it lets you keep a clear eye on the spinning metal as you cut. There are some complaints from people about the blue paint rubbing off on wood boards, but you can usually just wipe off that paint with your hand. It works effectively on most types of boards and can handle those already painted or stained.
Each of the 80 teeth on this model have a sharp point that you can sharpen later. Those teeth grip to the wood to create a smoother and more even cut surface.
Has 80 individual teeth that grip to the wood to smooth out its cuts
Cuts thinner and thicker boards including painted or otherwise finished boards
Bright blue finish makes it easy to keep your eyes on the surface as it spins
May cause some transfer of the blue paint on its finish onto the wood
Does not work well on thicker types of wood
7. HICO 40-Tooth ATB
While other products run so loudly that you cannot hear yourself think, this HICO model has built-in vents that absorb some of those noises to help it run quieter and more smoothly. Those vents also help it run at a lower temperature, which keeps it from overheating. As it has a standard 5/8-inch arbor, this one will work with most tables.
The high-density carbide used in its construction gets a boost from some titanium that makes it even stronger. It works well on most forms of hardwood as well as some softer woods and can work on plywood and chip board too.
Has a standard 5/8-inch arbor
Made from a high-density carbide with the addition of some titanium
Built-in vents keep it from overheating and reduces the noises produced
Has a larger run out than other products do
Larger distance between teeth may cause some splintering of the wood
8. INGTERCO 80-Tooth ATB
Though INGTERCO makes a variety of different products, this 80-tooth model is the one that caught our eye. Those teeth have a nice design that incorporates a flat top with a sharp edge that allows each teeth to sink into the wood before cutting it. Regular sharpening will increase the lifespan of those teeth.
Made from a titanium carbide, this model provides sharper cuts and lasts longer than products made from other materials. It works at a rating of up to 6,000 revolutions per minute and can handle both standard and cross cutting methods. This model also has a non-stick coating on its surface that helps the wood slip right off and prevents problems caused by friction.
Designed to reduce kickbacks and vibrations when spinning
Works with standard cutting and when doing cross cutting
Suitable for use at an RPM of up to 6,000
Requires regular sharpening of the tips
May not last as long as other products do in your table
9. Overpeak for Hard and Soft Woods
This Overpeak product is part of its Construction line, which professionals can use for all their cutting needs. It features 80 sharp teeth that you can sharpen on your own to make it last longer. Those teeth have a sharp point that moves through wood without breaking or chipping that wood, and you can use this model on both harder and softer varieties of wood, including plywood, chip board, maple and pine.
Though this model is quite sharp, it doesn’t quite measure the 10 inches listed by the manufacturer. It may leave behind a small gap that you need to take care of when using it in your table.
Sharp enough for using on harder woods without causing any chipping or breaking
Features ground teeth that you can sharpen on your own
Features 80 high-quality teeth around the sides
Leaves behind rougher edges when not properly sharpened
May not measure exactly 10 inches in size
10. IRWIN Tools Classic Series Steel
For grinding and other types of woodworking applications, this model from IRWIN Tools performs better than others. It has a solid plate in the center that extends out to the sides, which will last longer, but it also has 180 individual teeth that are sharp to the touch. Though those teeth can break off, regular maintenance will prevent that from happening.
The teeth on this product are precision ground, which ensures that each one is the same size and just as sharp as the next. We also like this one because its low price makes it an affordable option for any woodworker.
Affordable enough for all budgets
Has a total of 180 teeth for faster and more efficient grinding
Solid plate allows this model to last longer than its competitors
Has a speed rating that is too slow for use with some saws
Some teeth can break apart and come off before you can sharpen them
After looking at cheaper models and products from different companies, we found that the Forrest Woodworker II is really the best one around. It has ATB teeth around the edges that help it come to a complete stop when the saw stops and a design that keeps the wood you use from splintering as you cut it. This one doesn’t jump the way that others do either.
Made to install more easily, the Woodworker II cuts down on the wood that you usually lose when cutting. It also works in both crosscut as well as rip applications and lets you more easily feed your boards across.
To view more table saw reviews, visit this link.
How to Choose the Perfect One
How Many Teeth Does it Have?
One thing to consider is the number of teeth found on the product. You’ll usually need to choose between those that use 40 or 80. While many assume that those with more teeth are stronger, the proximity of each tooth to the next can actually make the wood splinter or chip because one tooth goes right over an area already cut by another.
What Type Do You Need?
Products designed for framing applications typically have around 25 teeth or less, but those designed for use with plywood have 100 teeth or more. This is because plywood is weaker and thinner than framing materials. Having more teeth helps cut the wood more smoothly without the plywood splintering.
There are also hollow ground models that have a hollow body and thicker teeth that keep the product balanced. You may want to look at kerf models that are lightweight and thinner to reduce the wood waste that you create.
What Size Does Your Table Require?
Always look at the size blade that your table uses before purchasing a new one. Most require a 10-inch size, but some need a 12-inch size. There are some that are compatible with both sizes too.
Larger blades of a 12-inch size are better for use with harder and thicker types of woods and boards. These larger sizes can create cuts more quickly also.
Does the Configuration of the Teeth Matter?
The configuration or design of the teeth really do matter. You might need a flat top configuration when doing rip cuts because the flat design of these teeth provide a smooth cut that won’t damage the wood. Others come with a beveled, alternating beveled or combination design that uses two or more designs.
You’ll also find something called a shoulder design, which is when the manufacturer adds more metal to the top of each tooth to create a piece that looks like a shoulder behind each one. This design puts more force behind those teeth and can keep the teeth sharper for longer.
Is One Material Better Than Another?
Some of the cheapest products that you see available online and in home improvement stores use aluminum. While once a precious and expensive metal, aluminum is now one of the cheapest materials around. A product made from this material may only last for a few months or even less.
Carbide is the top material because it extends the life of the teeth and the plate. You’ll also find products that use steel or titanium.